Technology |
Epoxy |
Chemical Type |
Epoxy |
Appearance (Resin) |
White |
Appearance – Mix |
White Liquid Mixture |
Components |
2-part components – Resin & hardener |
Mix ratio (Weight) Resin: Hardener |
4,5 : 1 |
Polymerisation |
At ambient temperature after mixing |
Application |
Anti-wear Coating |
Application Temperature |
15 – 30°C |
Service Temperature |
-30 : 90°C |
Benefits |
Reinforcement with Ceramic – for excellent abrasion resistanceReduced working timeBrushable – very smooth consistency, extremely glossySuperior adhesionVery low coefficient of friction |
SARPOL RP17 is an epoxy product with ceramic fill which is extremely smooth and provides a high-gloss finish, a low coefficient of friction ideal for protecting against abrasion and turbulence at typical dry operating temperatures ranging from -30 °C to 90 °C. Used on its own, SARPOL RP17 is recommending for sealing and protecting equipment from corrosion. It is also used as a layer to apply to SARO coatings for applications requiring the rebuilding of a surface and long-lasting protection. Typical applications involve the creation of a wear-resistant coating: repairing heat exchangers and condensers, alignment of tanks, chutes, repositioning and repair of drawbar housings, as well as the repair of cooling pumps and throttle valves.
Properties of Part A:
Density @ 25 C, ISO 1675, g/cm³ 1.85
Brookfield viscosity – RV, 25 °C, mPa·s (cP):
Spindle 7, speed 20 rpm 120 000-180 000
Properties of Part B:
Density @ 25 °C, ISO 1675, g/cm³ 1.05
Brookfield viscosity – RV, 25 °C, mPa·s (cP):
Spindle 2, speed 20 rpm 500-900
Properties of A + B Mixture:
Density @ 25 °C, ISO 1675, g/cm³ 1.81
Cone & Plate viscosity, 25 °C, mPa·s (cP):
Velocity Gradient 10 s-1 17 000
Hardening Properties
Open Time, ASTM D2471 minutes: 35
Time between coats @ 25 °C, hours: 1 – 3
Polymerisation Time @ 25 °C, hours: 5
Coverage
To achieve a thickness of 0.5 mm, coverage of 1.1 m² per 1 kg will be achieved.
GENERAL INFORMATION
This product is not recommended for use in systems rich in oxygen and/or pure oxygen and must not be selected as a sealant for chlorine or other strong oxidising agents.
For information on the safe handling of this product, consult the safety data sheet (SDS).
Surface Preparation
Surface preparation is important for the long-term performance of the product. The parameters may vary depending on the severity of the application, durability expectations and initial conditions of the substrate to be treated.
Method of Application
The second coats must be made once the layer of product has gelled but not polymerised, within the “overcoating time”. If this time is exceeded, the surface will need to be lightly scuffed and cleaned with solvent to eliminate residue.
Check:
Important: Use an approved self-contained respirator when cutting or welding near the hardened compound. Do not use naked flames on the compound..
Repairs
All untreated areas or porosity or areas with insufficient measured thickness must be restored or repaired by applying additional product, after lightly scuffing and cleaning the surface.
Cleaning
Clean tools immediately after use with a solvent such as acetone or isopropyl alcohol. Once hardened, the product can only be removed via mechanical means.
4
I dati tecnici qui contenuti sono da intendersi esclusivamente come riferimento. Si prega di contattare il reparto tecnico per l’assistenza e le raccomandazioni sulle specifiche per questo prodotto.
Stoccaggio
Conservare il prodotto nel contenitore chiuso in un luogo asciutto. Le informazioni di stoccaggio possono essere indicate sull’etichettatura del contenitore del prodotto.
Conservazione ottimale: da 8 a 21 °C. Lo stoccaggio inferiore a 8 °C o superiore a 28 °C può influire negativamente sulle proprietà del prodotto. Il materiale rimosso dai contenitori può essere contaminato durante l’uso. Non restituire il prodotto al contenitore originale. SARO Srl non può assumersi la responsabilità per il prodotto contaminato o conservato in condizioni diverse da quelle precedentemente indicate. Se sono necessarie ulteriori informazioni, si prega di contattare l’assistenza tecnica o il rappresentante/venditore di zona.
Le informazioni fornite in questa scheda tecnica (TDS) comprese le raccomandazioni per l’uso e l’applicazione del prodotto si basano sulla conoscenza ed esperienza dello stesso alla data di questa TDS. Il prodotto può avere una varietà di applicazioni diverse, nonché diverse condizioni di applicazione e di lavoro nell’ambiente di utilizzo al di là di ogni controllo. SARO Srl, pertanto, non è responsabile dell’idoneità del prodotto ai processi e alle condizioni di produzione per i quali esso è utilizzato, nonché delle applicazioni e dei risultati previsti. Si consiglia vivamente di effettuare le proprie prove per confermarne l’idoneità. È esclusa qualsiasi responsabilità in relazione alle informazioni contenute nella scheda tecnica o in qualsiasi altra raccomandazione scritta o orale riguardante il prodotto.
SARO Srl nega espressamente tutte le garanzie espresse o implicite, comprese le garanzie di commerciabilità o idoneità per uno scopo particolare, derivanti dalla vendita o dall’uso dei prodotti di SARO Srl. SARO Srl declina espressamente qualsiasi responsabilità per danni conseguenti o incidentali di qualsiasi tipo, compresi i profitti persi.